General fault solution

A,

Phenomenon: locator host does not start

Reason: 1, the power supply problem 2, fusing 3, 4, damage to the power switch, power supply cable break 5, line connection problem

Countermeasures: 1, to check whether there is electric power supply. Check the host power socket fuse fusing, replace the fuse. Check the cable

Is disconnected, replace the new cable. Check whether the power switch is damaged, replace the power switch. Check the power cord is correct

Pick up. If you still can't start, please contact the technical personnel of the company.

Second,

Phenomenon: no screen displays

Reason: 1, display the power switch didn't open the 2, 3, display data line not connected well or computer display card problem.

Action: check whether display power supply in the open position. Check whether the data line is connected well. Check whether the computer is normal. Please contact with the local meter

Computer services company technical personnel contact.

Three,

Phenomenon: don't show Microsoft Windows

Reason: 1, computer hardware failure, or Windows software problems. 2, computer hardware failure

Countermeasures: please contact the local computer services company technical personnel, check the computer Windows software Settings. If the computer technicians judgment

Need to reinstall the positioning software, please contact the technical personnel of the company.

Four,

Phenomenon: after entering Microsoft Windows, bo far locating software does not appear.

Reason: 1, the Windows startup profile software problem. 2, rich far software were damaged.

Countermeasures: please contact the local computer services company technical personnel, check whether bo far software in Microsoft Windows startup Settings. Need to be

Reinstall the positioning software, please contact the technical personnel of the company.

Five,

Phenomenon: in the positioning in the operation of the software, the program to a sudden stop.

Reason: the computer power grid voltage disturbance

Countermeasures: synchronous select CTRL key twice, ALT, and DEL keys. If the screen does not reflect, please close the control cabinet power supply. When the power is to open,

The computer software startup the computer automatic inspection. At the same time should be the main cabinet, computer shell connected to the earth. If you still can't start,

Please contact the technical personnel of the company.

Vi.

Phenomenon: sensor off the machine

Reason: 1, the batteries are 2, 3, damage to the sensor, power supply circuit breakers

Countermeasures: open the casing to check if the battery voltage, battery voltage is lower than 6.2 V, please recharge, please replace the battery if no voltage. electricity

Pool has electricity, check whether the circuit is broken wires, plugs out, plug contact are in good condition. Change electric wire, plug plug retry, if you still

Can't boot, please contact the technical personnel of the company.

Seven,

Phenomenon: sensors can't charge.

2 reasons: 1, the charger is damaged, charging a bad contact 3, line break line 4, damage of the battery

Action: check the charger input, if there is no input voltage, output voltage according to the power supply before inspection. If there is no output voltage charging

Whether the fuse fusing, replace the fuse, if not, please contact the technical personnel of the company. Observe charging a small box of instructions

Lights, all the light not bright, under normal conditions for slow charging status under the green light is shining, quick charge state red light, green light flash faster. When the mass

Sensor on the charging seat lamp don't light sensor with good charge without contact, adjust the sensor to try, if still no electricity

Can the battery is damaged, replace the battery. If you still can't charge electricity check line for break. If you still can't work, please contact with our company

The technical personnel contact.

Eight,

Phenomenon: when measuring software has been display individual sensor warning window.

Reason: 1, the sensor power supply problem 2, rechargeable batteries. 3, sensor communication Windows smudgy

Action: check whether the power light sensors is lit. Replace the rechargeable battery. With clean soft cloth to clean the sensor communication window. If you still don't

Able to work, please contact the technical personnel of the company.

Nine,

Phenomenon: when measuring software warning window shows individual Angle of the CCD sensor without reading.

Reason: 1, 2, sensor CCD sensor with obstructions between Angle sensor window smudgy

Countermeasures: in the measurement of note don't walk about in between sensors or place objects. Clean the CCD beam Angle sensor with lens paper Windows. If you still

Can't work, please contact the technical personnel of the company.

Ten,

Phenomenon: when measuring software warning window always shows individual inclination sensor without reading.

Reason: sensor failure

Action: please contact the technical personnel of the company

Eleven,

Phenomenon: no print data

Reason: 1, the power supply problem 2, 3 printer cable, no print paper

Countermeasures: to check whether there is electric power socket, check the printer cable connected to machine is correct. Check that the printer switch is on. play

If there is a paper printing machine, printer ink cartridge is used up. If you still can't print, the local contact computer services company technical personnel.